Products /


Kalia İpek Mat
Water Based Interior Wall Paint

Product Definition
Acrylic emulsion based, photocatalytic (activated by light), mildew and algae resistant, silicone enhanced, easy to clean, perfectly scrub resistant, silky matt interior wall paint.

Application Areas
> On interiors suitably prepared new mineral surfaces such as concrete, mortar, cement panel, gypsum panel etc. and on old painted surfaces, putty, glass textile and on wallpaper.

> Photocatalytic; by the activation of light it decomposes the harmful materials such as nicotine fume and bad odours transferred by air movements on interior surfaces. Therefore, cleans the air in the room and enables walls to remain clean for a long time.
> Silicone enhanced. Cleanable with its perfect scrub resistance therefore stain free.
> Provides relief for those suffering from asthma in particular by resisting against algae and mildew growth.
> Easily re-touchable, does not leave brush or roller marks.
> High water vapour permeability, allowing the building to breathe.
> Superior hiding power.
> Solvent free and practically odourless.
> Water thinnable and ecologically compatible.

Technical Features
(at 23°C and 50% RH)

General Data:
Colors: Thousands of colors possible from a mixture of white and A, B, C bases using the Renk Bankası and the Renk Ustası.
Composition: Acrylic emulsion based
Thinner: Water
Density Approx.: 1.35 gr/cm³

Application Data:
Application Temperature Range: (+5°C) - (+35°C)
Drying Time: Recoatable after 6 hours and thoroughly dry after 24 hours.
Lower temperatures and/or higher relative humidity will lengthen the drying process.
Consumption: Depending on the evenness and the porosity of the surface approximately 0.090 lt/m² per coat.
Application Tools: Brush, Roller, Airless spraying equipment

Performance Data:
Water Vapour Permeability SD (m) (TS EN ISO 7783 - 2): Approx. 0.250
Scrub Resistance (cycle) (ASTM 2486): > 500
Gloss (60°) (ISO 2813): Approx. 7
Service Temperature: (-30°C) - (+80°C)

TS EN 13300: Classification
Wet Scrub Resistance: Class 1
Contrast Ratio: Class 1 (5.5 m2/lt)
Largest Grain Size: Class S1
Gloss: Class G2
Fungi and Algae Resistance: Class K1

Application Instructions
> The substrate must be cleaned from dust, dirt, oil and old blistered coatings that may prevent good adhesion. The surface should be made sound, clean and dry. New cementitous substrates must be cured at least 28 days before application.
> Before application on old painted mouldy surfaces; clean the surface with a wet cloth and treat with 2-3 successive wet-on- wet coats of Kale KÜF TEMİZLEYİCİ in order to kill the mould on the wall.
> Sand glossy and/or solvent based painted surfaces to improve adhesion and remove the occurring powder.
> If necessary, fill the surface cracks and even the substrate with Kale İNCE AKRİLİK MACUN or Kale Macunart.
> To have a fine, silky texture, smoothen the entire surface by using Kale İNCE AKRİLİK MACUN or Kale MACUNART.
> Prime the solvent based painted surfaces or water based painted surfaces on which color change is desired and old painted water based and very dirty surfaces with Kale SİLASTAR and new and porous surfaces with Kale SATEN ALÇI ASTARI or Kale SİLASTAR.
> After thoroughly mixing, thin KALİA İPEK MAT with clean water up to a maximum of 10% by volume and apply in two coats by using a brush, roller or spray system.
> Wait for a minimum of 6 hours before applying the final coat
> Clean the tools with water.
> Ensure that the air and surface temperatures are above 5°C during the application and 24 hours following the application.


> S2 Keep out of the reach of children.
> S24/25 Avoid contact with skin and eyes.
> S46 If swallowed, seek medical advice.

> Store between 5°C-35°C in its unopened pail.

> 2.5 lt, 7.5 lt and 15 lt pails.
> 2.5 lt packages packed together in 2s.

Quality Documents
TS 5808

Back Back  Top Top Print Print


Kale Kalekim Corporate                  Kalekim Facebook Kalekim Blog Kalekim Twitter

Türkçe    > English    Русский