Products /


Water Based, Exterior Wall Paint

Product Definition
Ceramic micro spheres and silicone enhanced, mildew and algae resistant, water impermeable, acrylic emulsion based, long lasting, matt, exterior wall paint.

Application Areas
> On exterior mineral surfaces such as concrete, mortar, cement panel, etc. and on previously painted surfaces.

> Contributes to heat insulation with its ceramic micro spheres.
> Water repellent; provides rain to slide away without wetting the wall.
> Resistant againt mildew and algae growth on walls.
> Water resistant.
> Superior hiding power
> High water vapour permeability, allowing the building to breathe.
> Long lasting, resists to UV rays, rain, heat and frost, thus retains its original properties for years without cracking, blistering and fading.
> Alkali resistant.
> Water thinnable and ecologically compatible.
> Solvent free and practically odourless.

Technical Features
(at 23°C and 50% RH)

General Data:
Colors: Thousands of colors possible from a mixture of white and A, B, C bases using the Renk Bankası and the Renk Ustası.
Composition: Acrylic emulsion based
Thinner: Water
Density: Approx. 1.52 gr/cm³

Application Data:
Application Temperature Range: (+5°C) - (+35°C)
Drying Time: Recoatable after 6 hours and thoroughly dry after
24 hours.
Lower temperatures and/or higher relative humidity will lengthen the drying process.
Consumption: Depending on the evenness and the porosity of the surface approximately 0.130 lt/m² per coat.
Application Tools: Brush, Roller, Airless spraying equipment

Performance Data:
Water Vapour Permeability SD (m) (TS EN ISO 7783 - 2):
Approx. 0.150
Scrub Resistance (cycle) (ASTM 2486): > 300
Gloss (60°) (ISO 2813): Approx. 3
Water Absorption (kg/m² h0.5) (TS EN 1062 - 3): < 0.100
Service Temperature: (-30°C) - (+80°C)

TS EN 1062-1: Classification
Gloss: Class G3
Film Thickness: Class E3
Grain Size: Class S1
Water Vapour Transmission: Class V1
Liquid Water Permeability: Class W3
Crack Bridging: Class A0
CO2 Permeability: Class C0
Fungi and Algae Resistance: Class K1

Application Instructions
> The substrate must be cleaned from dust, dirt, oil and old blistered coatings that may prevent good adhesion. The surface should be made sound, clean and dry. New cementitous substrates must be cured at least 28 days before application. All water insulation precautions should have been taken prior to application.
> Sand glossy and/or solvent based painted surfaces to improve adhesion and remove the occurring powder.
> If necessary, fill the surface cracks and even the substrate with Kale KALIN AKRİLİK MACUN, Kale MACUNART or Kalekim TAMİRART.
> Prime new mineral and old painted surfaces with Kale ÜNİASTAR or SİLASTAR.
> After thoroughly mixing, thin PROTEKTA with clean water up to a maximum of 10% by volume and apply in two coats by using a brush, roller or spray system.
> Wait for a minimum of 6 hours before applying the final coat.
> Clean the tools with water.
> Ensure that the air and surface temperatures are above 5°C and the surface is rain free during application and 24 hours following the application.
> Do not apply in extremely hot weather, under glaring sun, during strong wind, fog, high relative humidity and imminent rain or frost.
> Dampen the hot surfaces before the application.
> Not suitable for application on horizontal surfaces exposed to rain or moisture.


> S2 Keep out of the reach of children.
> S24/25 Avoid contact with skin and eyes.
> S46 If swallowed, seek medical advice.

> Store between 5°C-35°C in its unopened pail.

> 2.5 lt, 7.5 lt and 15 lt pails.
> 2.5 lt packages packed together in 2s.

Quality Documents
TS 7847

Back Back  Top Top Print Print


Kale Kalekim Corporate                  Kalekim Facebook Kalekim Blog Kalekim Twitter

Türkçe    > English    Русский